問題詳情
57. According to this article, the deeper goal of education to the author is ________.
(A) to distribute more information and better knowledge to students
(B) to guide students to build up their own anticipations and aims of life
(C) to teach students what are the best role models of intelligence and moral qualities for them to learn
(D) to show students good skills and right knowledge to be useful persons
(E) to give the excellent qualities of knowledge to students
(A) to distribute more information and better knowledge to students
(B) to guide students to build up their own anticipations and aims of life
(C) to teach students what are the best role models of intelligence and moral qualities for them to learn
(D) to show students good skills and right knowledge to be useful persons
(E) to give the excellent qualities of knowledge to students
參考答案
答案:B
難度:適中0.6
統計:A(1),B(3),C(1),D(0),E(0)
內容推薦
- Passage 4 (Questions 56-60):True learning is not a matter of the formal organization of knowledge of
- 四、CATIA V5 草圖(Sketch)繪製過程中,經常需要使用拘束(Constraint )功能來控制幾何圖形,請回答下列問題 :(一)列出任意 2 個圓形之間的 5 種拘束(Const
- (4)點選加強肋(Stiffener)指令,設定肋厚,選取肋板草圖,建立加強肋實體。
- (三)圓孔之幾何公差標示如下,請說明代表之意義。(6 分)
- (3)點選旋轉成形(Shaft)指令,選取螺桿草圖,旋轉 360 度,建立螺桿實體。
- (二)試列舉尺寸公差的種類,並簡述之。(4 分)
- (2)插入一個新的組合件(Product)。
- 如右圖所示之橋式整流電路,假設二極體均為理想二極體,當輸入交流電壓Vin(t)大於0伏特時,請問二極體的狀態,下列何者正確?) (A)DD3導通,DD4不導通(B)DD4導通,DD
- 在解釋憲法時,觀察全部條文,用邏輯的方法,斟酌立憲意旨,背景及目的,確定該條文之意義,稱為:(A) 文理解釋 (B)綜合解釋 (C)類推解釋 (D)論理解釋
- 三、請回答下列有關公差之問題:(一)何謂公差?(5 分)
內容推薦
- 下列哪一種材料常用於製作螺絲起子等各式工具?(A)低碳鋼 (B)鑄鐵(C)純鋁 (D)高碳鋼
- (2)過度拘束(Over-Constraint)(5 分)
- Which of the following statements is NOT one of the main ideas in this article?(A) The true
- (二)常用銲料
- 虎鉗規格以下列何者表示之?(A)虎鉗重量 (B)鉗口寬度(C)虎鉗材質 (D)虎鉗高度
- 五、請回答下列有關 CATIA V5 組裝設計(Assembly Design)之問題 :(一)將零件(Part)移動到適當組合位置之搬移 (Manipulation ) 指令,可以歸納為哪
- According to the article, the true purpose of a teacher is __________.(A) to help her/his st
- (三)常用銲劑
- (二)零件搬移完成之後,可以使用碰撞檢測(Clash)檢查零件之間是否發生干涉,請說明碰撞檢測可分為哪 2 種形式(Type)? (6 分)
- (四)用途
- 六、下圖所示之模線卡塊(contour board),係使用於定位曲面薄板。模線卡塊之內模面必須與曲面薄板外模面完全貼合(contact)。假設曲面薄板之 CATIA V5 零件(Part)
- 提示(二) : 建構步驟用語格式範例如下 : (注意範例內容未必與答案相關)(1)進入草圖繪製(Sketcher)模式。
- 一人向北行10 m,轉向東行5 m,再轉向南行5 m,其位移量爲多少m ?(A)5(B) (C)10(D)15
- ECL (Emitter-Coupled Logic)電晶體邏輯閘的優缺點中,下列何者敘述有誤?(A)雜訊邊界大 (B)可以有互補輸出 (C)輸出可直接連結 Wired-OR (D) Fan-o
- 下圖的邏輯表示是 。
- (二)有大眼睛的生物;
- 質量為 m 的物體沿底面長度均為 L,傾斜角不同的 a、b、c 三個斜面從頂端滑下,若物體與斜面間的動摩擦係數相同,a、b、c 三個傾斜角關係是 θ1>θ2>θ3(如圖所示),該物體從 a、b、
- 如【圖 40】所示電路,二極體的耐壓(PIV)不得小於幾伏特?(A) 10 V(B) 14 V(C) 20 V(D) 28 V
- (三)有大眼睛和發光器的生物;
- 右【圖 1】所示的電路作用為下列何者? (A)積分器 (B)微分器(C)限制器 (D)整流器
- (四)具有退化眼睛的生物?(20 分)
- 下列何者為計算雙邊規格之製程能力指數 Cp?(A) T/(Su-SL) (B) T/3σˆ (C) T/6σˆ (D) 6σˆ /T
- 請依視圖選出正確之立體圖 (A) (B) (C) (D)
- 二、試說明⑴極地附近海域;
- 下列選項中,何者符合「一份文件明確敘述品質管理流程與運用在特定產品、專案或合約的資源」之敘述?(A)品質計畫 (B)品質監督 (C)品質管制 (D)品質保證